dunno
guessing guards, bonnets , lights , front bar ???
rta doesnt need to know
| Silvia Club of NSW https://silviansw.com/forum/ |
|
| how do i make a sil80 https://silviansw.com/forum/viewtopic.php?f=4&t=10527 |
Page 1 of 1 |
| Author: | Quinn [ Sun Aug 01, 2004 12:50 pm ] |
| Post subject: | how do i make a sil80 |
i have 180sx and want to put the silvia front on it, what mods need to be done to the chassis or is it a straight change bolt on proceedure, does the RTA or an engineer need to be informed |
|
| Author: | fullboost [ Sun Aug 01, 2004 4:21 pm ] |
| Post subject: | |
dunno guessing guards, bonnets , lights , front bar ??? rta doesnt need to know
|
|
| Author: | renz [ Tue Aug 03, 2004 1:21 am ] |
| Post subject: | |
quinn- hey man, depending on how much it would cost. I'd be interested in swapping front ends with you. I've got a 91 S13 silvia. Not entirely sure which parts we need to swap and how much it's going to cost though. I know this subject's been brought up before, pm me if your interested or know of someone who can do the change. Thanks Ren 
|
|
| Author: | renz [ Tue Aug 03, 2004 1:51 am ] |
| Post subject: | |
parts needed... (thanks gunmetal and cmy513): http://www.silviansw.com/forum/viewtopi ... conversion This is for a onevia conversion, i'd imagine the parts needed would be similar for a sil80. Thanks Ren |
|
| Author: | YXP05E [ Wed Aug 04, 2004 7:37 pm ] |
| Post subject: | |
it's pretty much swap the whole front end on both cars.... they are all bolt in as the chassis is the same thing... only problem u'll have is wiring up the headlights... the 180 front will have to have motors to put the headlights up... but look into it... i've got a silvia front on my car and its not hard... bolt in.. RTA dont need to know nothing... "u brought it like that" hehehe
|
|
| Author: | mayhem [ Thu Aug 05, 2004 12:18 am ] |
| Post subject: | |
As previously mention its a pretty straight foward swap, the main problem being the headlight wiring. |
|
| Author: | SYCO 1VA [ Thu Aug 05, 2004 3:27 pm ] |
| Post subject: | |
going from 180 front end to silvia front is a bit easier in terms of wiring cos you dont need to connect the 5 wires to run the headlight motors. And if you swap with someone, be nice and give them the relays so the headlights can function as the nissan factory intended. |
|
| Author: | Quinn [ Fri Aug 06, 2004 6:24 pm ] |
| Post subject: | |
thanks guys for the help, i thought it would be pretty simple to do the change over. does anyone know where i can get the parts as cheap as possible, or find a half cut with panels also cheap. |
|
| Author: | YXP05E [ Fri Aug 06, 2004 6:57 pm ] |
| Post subject: | |
depends on wat u want.... like u can source the parts out urself... it's a good opportunity to dress ur car up... widebody front guards, carbon fibre bonnet, front bar, and someone will have some headlights ... eg.. i have silvia head lights ... hehehe
|
|
| Author: | SYCO 1VA [ Tue Aug 10, 2004 4:33 pm ] |
| Post subject: | |
just shop around at various jap wreckers for the body panels...or look for wide guards, carbon fibre bonnet, and aftermarket front bar for a wicked looking Sil80 |
|
| Author: | Quinn [ Sat Aug 21, 2004 3:26 pm ] |
| Post subject: | |
does anyone know where to get the phat wide body gaurds and that stuff |
|
| Author: | Nismodified [ Sat Aug 21, 2004 9:38 pm ] |
| Post subject: | |
MFX_R33 on these forums sells them i believe, give him a PM. Gamer on these forums has the MFX guards on his 180 |
|
| Author: | CRR000 [ Sun Aug 22, 2004 9:54 pm ] |
| Post subject: | |
what colour is your 180? i got a black silvia with a brand new vertex front bar (never been on the car) and am looking at a onevia swap u interested? all panels are perfect |
|
| Page 1 of 1 | All times are UTC + 10 hours [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|