Silvia Club of NSW https://silviansw.com/forum/ |
|
ECUTalk consult software https://silviansw.com/forum/viewtopic.php?f=12&t=21037 |
Page 4 of 4 |
Author: | NewKleer [ Sun May 18, 2008 11:16 am ] |
Post subject: | |
ECUTalk v1.3.3 - Changes from v1.3.3 beta4 below:
|
Author: | NewKleer [ Sun Feb 28, 2010 10:56 am ] |
Post subject: | |
back in june v1.3.4 was released which was a minor release, just allowing COM10-COM19 ports to be used, and also alternative ECU ID (e.g. E7 instead of EF) to be used. there is a beta of ECUTalk v1.3.5 which adds alerts - define alerts for battery voltage, temperature, injector duty cycle, speed, airflow and RPM, and the gauge will flash (invert colours) and beep if an alert is hit ECUTalk v1.3.4 - Changes from v1.3.3 below:ECUTalk v1.3.5 beta - Changes from v1.3.4 below:
|
Author: | NewKleer [ Wed May 19, 2010 12:48 pm ] |
Post subject: | |
ECUTalk v1.3.5 beta3 which adds proper support for diesel engines, including diesel specific sensors, also update to error codes. ECUTalk v1.3.5 beta3 - Changes from v1.3.5 beta1 below:
|
Author: | NewKleer [ Fri Jul 16, 2010 12:58 pm ] |
Post subject: | |
ECUTalk v1.3.5 beta6 has been released, which heaps of switch/solenoid sensors. ECUTalk v1.3.5 beta6 - Changes from v1.3.5 beta3 below:
|
Author: | NewKleer [ Mon Jan 10, 2011 10:03 am ] |
Post subject: | |
ECUTalk v1.3.5 final has been released (along with beta 7 before it), which mainly just adds support for Active Suspension control unit (on Q45 Infiniti and similar) amongst other minor changes: ECUTalk v1.3.5 final - Changes from v1.3.5 beta6 below:
|
Author: | DumHed [ Mon Jan 10, 2011 7:33 pm ] |
Post subject: | |
awesome! Will have to check it out now that I have a car with consult again |
Author: | ZEi250t [ Tue Jan 11, 2011 8:33 pm ] |
Post subject: | |
these dont work on V35s and M35s do they? they are consult3 if that helps |
Author: | NewKleer [ Tue Jan 11, 2011 9:04 pm ] |
Post subject: | |
No, sorry, only the original consult vehicles (up to R34). Check out blazt/datascan2 i think it works with some of the v35 range. |
Author: | ZEi250t [ Fri Jan 14, 2011 6:16 pm ] |
Post subject: | |
thanks mate, unfortunately it doesnt work with ours the greddy informeter does, which is what i have at the moment |
Author: | NewKleer [ Fri Jan 14, 2011 6:59 pm ] |
Post subject: | |
thats via OBDII i'd assume? does that mean scangauge should work? |
Author: | ZEi250t [ Fri Jan 21, 2011 5:43 pm ] |
Post subject: | |
its different i think, it talks CANBUS or something else. |
Page 4 of 4 | All times are UTC + 10 hours [ DST ] |
Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |